GSM Timers

Timers on the mobile station side

T3122: This timer is used during random access, after the receipt of an IMMEDIATE ASSIGN REJECT message. Its value is given by the network in the IMMEDIATE ASSIGN REJECT message.

T3124: This timer is used in the seizure procedure during a hand-over, when the two cells are not synchronized. Its purpose is to detect the lack of answer from the network to the special signal. Its value is set to 675 ms if the channel type of the channel allocated in the HANDOVER COMMAND is an SDCCH (+ SACCH); otherwise its value is set to 320 ms.

T3126: This timer is started either after sending the maximum allowed number of CHANNEL REQUEST messages during an immediate assignment procedure. Or on receipt of an IMMEDIATE ASSIGNMENT REJECT message, whichever occurs first. It is stopped at receipt of an IMMEDIATE ASSIGNMENT message, or an IMMEDIATE ASSIGNMENT EXTENDED message. At its expiry, the immediate assignment procedure is aborted. The minimum value of this timer is equal to the time taken by T+2S slots of the mobile station’s RACH. S and T. The maximum value of this timer is 5 seconds.

T3128: This timer is started when the mobile station starts the uplink investigation procedure and the uplink is busy. It is stopped at receipt of the first UPLINK FREE message. At its expiry, the uplink investigation procedure is aborted. The value of this timer is set to 1 second.

T3130: This timer is started after sending the first UPLINK ACCESS message during a VGCS uplink access procedure. It is stopped at receipt of a VGCS ACCESS GRANT message. At its expiry, the uplink access procedure is aborted. The value of this timer is set to 5 seconds.

T3110: This timer is used to delay the channel deactivation after the receipt of a (full) CHANNEL RELEASE. Its purpose is to let some time for disconnection of the main signaling link. Its value is set to such that the DISC frame is sent twice in case of no answer from the network. (It should be chosen to obtain a good probability of normal termination (i.e. no time out of T3109) of the channel release procedure.)

T3134:This timer is used in the seizure procedure during an RR network commanded cell change order procedure. Its purpose is to detect the lack of answer from the network or the lack of availability of the target cell. Its value is set to 5 seconds.

T3142: The timer is used during packet access on CCCH, after the receipt of an IMMEDIATE ASSIGNMENT REJECT message. Its value is given by the network in the IMMEDIATE ASSIGNMENT REJECT message.

T3146:This timer is started either after sending the maximum allowed number of CHANNEL REQUEST messages during a packet access procedure. Or on receipt of an IMMEDIATE ASSIGNMENT REJECT message during a packet access procedure, whichever occurs first. It is stopped at receipt of an IMMEDIATE ASSIGNMENT message, or an IMMEDIATE ASSIGNMENT EXTENDED message. At its expiry, the packet access procedure is aborted. The minimum value of this timer is equal to the time taken by T+2S slots of the mobile station’s RACH. S and T are defined in section 3.3.1.2. The maximum value of this timer is 5 seconds.

T3164: This timer is used during packet access using CCCH. It is started at the receipt of an IMMEDIATE ASSIGNMENT message. It is stopped at the transmission of a RLC/MAC block on the assigned temporary block flow, see GSM 04.60. At expire, the mobile station returns to the packet idle mode. The value of the timer is 5 seconds.

T3190: The timer is used during packet downlink assignment on CCCH. It is started at the receipt of an IMMEDIATE ASSIGNMENT message or of a PDCH ASSIGNMENT COMMAND message when in dedicated mode. It is stopped at the receipt of a RLC/MAC block on the assigned temporary block flow, see GSM 04.60. At expiry, the mobile station returns to the packet idle mode. The value of the timer is 5 seconds.

 

Timers on the network side


T3101
: This timer is started when a channel is allocated with an IMMEDIATE ASSIGNMENT message. It is stopped when the MS has correctly seized the channels. Its value is network dependent. NOTE: It could be higher than the maximum time for a L2 establishment attempt.
T3103: This timer is started by the sending of a HANDOVER message and is normally stopped when the MS has correctly seized the new channel. Its purpose is to keep the old channels sufficiently long for the MS to be able to return to the old channels, and to release the channels if the MS is lost. Its value is network dependent. NOTE: It could be higher than the maximum transmission time of the HANDOVER COMMAND, plus the value of T3124, plus the maximum duration of an attempt to establish a data link in multiframe mode.)
T3105: This timer is used for the repetition of the PHYSICAL INFORMATION message during the hand-over procedure. Its value is network dependent. NOTE: This timer may be set to such a low value that the message is in fact continuously transmitted.
T3107: This timer is started by the sending of an ASSIGNMENT COMMAND message and is normally stopped when the MS has correctly seized the new channels. Its purpose is to keep the old channel sufficiently long for the MS to be able to return to the old channels, and to release the channels if the MS is lost. Its value is network dependent. NOTE: It could be higher than the maximum transmission time of the ASSIGNMENT COMMAND message plus twice the maximum duration of an attempt to establish a data link multiframe mode.
T3109: This timer is started when a lower layer failure is detected by the network, when it is not engaged in a RF procedure. It is also used in the channel release procedure. Its purpose is to release the channels in case of loss of communication. Its value is network dependent. NOTE: Its value should be large enough to ensure that the MS detects a radio link failure.
T3111: This timer is used to delay the channel deactivation after disconnection of the main signaling link. Its purpose is to let some time for possible repetition of the disconnection. Its value is equal to the value of T3110.
T3113: This timer is started when the network has sent a PAGING REQUEST message and is stopped when the network has received the PAGING RESPONSE message. Its value is network dependent. NOTE: The value could allow for repetitions of the Channel Request message and the requirements associated with T3101.
T3115: This timer is used for the repetition of the VGCS UPLINK GRANT message during the uplink access procedure. Its value is network dependent. NOTE: This timer may be set to such a low value that the message is in fact continuously transmitted.
T3117: This timer is started by the sending of a PDCH ASSIGNMENT COMMAND message and is normally stopped when the MS has correctly accessed the target TBF. Its purpose is to keep the old channel sufficiently long for the MS to be able to return to the old channels, and to release the channels if the MS is lost. Its value is network dependent. NOTE: It could be higher than the maximum transmission time of the PDCH ASSIGNMENT COMMAND message plus T3132 plus the maximum duration of an attempt to establish a data link in multiframe mode.
T3119: This timer is started by the sending of a RR-CELL CHANGE ORDER message and is normally stopped when the MS has correctly accessed the new cell. Its purpose is to keep the old channels sufficiently long for the MS to be able to return to the old channels, and to release the channels if the MS is lost. Its value is network dependent. NOTE: It could be higher than the maximum transmission time of the RR_CELL CHANGE ORDER, plus T3134, plus the maximum duration of an attempt to establish a data link in multiframe mode.
T3141: This timer is started when a temporary block flow is allocated with an IMMEDIATE ASSIGNMENT message during a packet access procedure. It is stopped when the mobile station has correctly seized the temporary block flow. Its value is network dependent

About these ads